检索结果分析
成果/Result
成果类型
- 期刊论文
- 学位论文
- 专利
- 会议论文
- 科技成果
- 标准
- 专著
- 产品
- 科技报告
- 政策法规
- 内部文献
- 报纸
- Comprehensive error measurement and compensation method for equivalent cutting forces
- INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGYShi, Xianli Liu, Huanlao Li, Hao Liu, Can Tan, Guangyu 出版年：2016
- To determine the error compensation for cutting forces with a machine tool, this paper proposes a comprehensive error compensation method that determines an equivalent cutting force. The loading system that applies this ...
- Wear Mechanism of Cemented Carbide Tool in High Speed Milling of Stainless Steel
- CHINESE JOURNAL OF MECHANICAL ENGINEERINGLiu, Guang-Jun Zhou, Zhao-Cheng Qian, Xin Pang, Wei-Hai Li, Guang-Hui Tan, Guang-Yu 出版年：2018
- Adhesion of cutting tool and chip often occurs when machining stainless steels with cemented carbide tools. Wear mechanism of cemented carbide tool in high speed milling of stainless steel 0Cr13Ni4Mo was studied in this ...
- Experiment, modeling, and analysis for temperature field of milling insert
- INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGYLiu, Guangjun Tan, Guangyu Li, Guanghui 出版年：2009
- This paper presents a theoretical and experimental study of the dynamic temperature field on a milling insert with complex groove. Experimental measurements of milling temperature using the thermocouple technique were pe...
- Frequency-spectrum characteristics of force in end milling with tool wear and eccentricity
- INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGYLiu, Can Wu, Jing-quan Li, Guang-hui Tan, Guang-yu 出版年：2013
- The effects of chip load, tool wear, and tool eccentricity on milling force are similar; in order to distinguish them from each other, the spectral characteristics of milling force for four flute end mills was studied. W...
- Experimental study on adhesive wear of milling insert with complex groove
- INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGYTan, Guangyu Liu, Guangjun Li, Guanghui 出版年：2009
- This paper presents an experimental study on the adhesive wear of a milling insert with complex groove when milling 3Cr-1Mo-1/4V and 0Cr18Ni9 steels. Experimental measurements of milling temperature and milling force wer...
- MultidiSCIplinary design optimization of a milling cutter for high-speed milling of stainless steel
- INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGYLiu, Guangjun Tan, Guangyu Li, Guanghui Rong, Yiming Kevin 出版年：2013
- The milling cutter's fracture strength is more important than its chemical stability and thermal conductivity in high-speed milling. The multidiSCIplinary design optimization (MDO) method is employed to optimize the frac...
- Geometry features of breakage section and variation of cutting force for end mills after brittle breakage
- INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGYLiu, Can Wu, Jing-quan Liu, Huan-lao Li, Guang-hui Tan, Guang-yu 出版年：2016
- Some broken end mills with many brittle breakage sections were collected, and the geometry features of these sections were summed up. As for minor breakage, the breakage sections were narrow planes parallel to the tool e...
- Adhesive failure of grooved tool in milling of 3Cr-1Mo-1/4V steel
- INTERNATIONAL JOURNAL OF MATERIALS & PRODUCT TECHNOLOGYTan, Guangyu Liu, Guangjun Li, Guanghui 出版年：2011
- The adhesive failure of an uncoated cemented carbide tool was investigated in face milling of 3Cr-1Mo-1/4V stainless steel. The milling force and milling temperature were measured. The temperature field, stress field and...
