CHINESE JOURNAL OF MECHANICAL ENGINEERINGLiu, Guang-Jun Zhou, Zhao-Cheng Qian, Xin Pang, Wei-Hai Li, Guang-Hui Tan, Guang-Yu 出版年：2018
Adhesion of cutting tool and chip often occurs when machining stainless steels with cemented carbide tools. Wear mechanism of cemented carbide tool in high speed milling of stainless steel 0Cr13Ni4Mo was studied in this ...
Journal of Physics: Conference SeriesYin, Ningxia Li, Guanghui Tan, Guangyu Shen, Can Xue, Jiao 出版年：2018
In order to weaken the negative effect on environment and human health caused by the overuse of the cutting fluid, the internal cooling cutting is paid more and more attention. An end-milling with an internal cooling lub...
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGYLiu, Guangjun Tan, Guangyu Li, Guanghui 出版年：2009
This paper presents a theoretical and experimental study of the dynamic temperature field on a milling insert with complex groove. Experimental measurements of milling temperature using the thermocouple technique were pe...
ASME International Mechanical Engineering Congress and Exposition, Proceedings (IMECE)Tan, Guangyu Liu, Guangjun Li, Guanghui Rong, Yiming Song, Hui 出版年：2007
This paper presents a groove reconstruction method based on the local rule of Cellular Automata (CA). A local rule for groove reconstruction is proposed to design and optimize the groove of milling insert. The insert is ...
With the increasing spindle speed and the necessity existence of the cutting fluid, inner cooling milling is drawing more and more attention. In order to research the effect of cutting fluid on the inner cooling tool, a ...
International Journal of Control and AutomationZhengyu, Wang Xiaoyang, Yu Guanghui, Li Guangyu, Tan 出版年：2014
In order to measure cutter temperature, the on-line thermocouple temperature measurement system was proposed. In this system, temperature sensing element thermocouple was welded in the flank face close to the cutting edg...
This work aims to investigate parameterized modeling and a different mode of loading with finite element analysis for flat end mill. A loading mode is chosen according to the cutting force model of overall end mills. Nor...
This paper adopts with a PMAC Programmable Multi-axis Controller to control a linear motor through adjusting PID + velocity and acceleration feedforward parameters of the control card. The motor can reach 50-nm precision...
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGYLiu, Can Wu, Jing-quan Li, Guang-hui Tan, Guang-yu 出版年：2013
The effects of chip load, tool wear, and tool eccentricity on milling force are similar; in order to distinguish them from each other, the spectral characteristics of milling force for four flute end mills was studied. W...
International Journal of Manufacturing ResearchTan, Guangyu Liu, Guangjun Li, Guanghui Song, Hui Rong, Kevin Yiming 出版年：2008
A numerical method for modelling the temperature field of milling insert with 3D complex groove is proposed based on the self-organising Cellular Automata. The self-organising local rule of Cellular Automata is derived t...
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGYLiu, Guangjun Tan, Guangyu Li, Guanghui Rong, Yiming Kevin 出版年：2013
The milling cutter's fracture strength is more important than its chemical stability and thermal conductivity in high-speed milling. The multidisciplinary design optimization (MDO) method is employed to optimize the frac...
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGYTan, Guangyu Liu, Guangjun Li, Guanghui 出版年：2009
This paper presents an experimental study on the adhesive wear of a milling insert with complex groove when milling 3Cr-1Mo-1/4V and 0Cr18Ni9 steels. Experimental measurements of milling temperature and milling force wer...
This paper presents a self-organizing method for reconstruction of complex groove of milling insert. The local rule of Cellular Automata is proposed to design and optimize the groove of milling insert. The states of cell...
Advanced Materials ResearchLiu, Can Li, Guang Hui Wu, Jing Quan Tan, Guang Yu 出版年：2011
To compare the effects of different machining parameters on force in milling T10 hardened steel, the features of theoretical forces in up and down milling were analysised, and comparative experiments of milling force wer...
PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGYZhang, Ping Wang, Shunxiang Zhang, Junbao Zhang, Tengfei Li, Guohong 出版年：2025
This study investigates the wear mechanisms and grain refinement patterns of CoCrFeNiAlX series high-entropy alloy-coated tools during the micro-cutting of TC4 titanium alloy. Three coatings were selected: CoCrFeNiAl (Al...
Motorized spindle is an execution unit of machine tool. The rotation of a motorized spindle and the cutting of a machine tool are two vibration sources which will impact the feed system. These vibrations will affect proc...
Lots of cutting heat is generated in milling process, and an unsteady temperature distribution is generated, which is the radical reason of impactive fracture and sticking-welding fracture of the tool. In this paper, the...
Solid State PhenomenaLi, Guang Hui Wu, Peng Ni, Xiao Long Peng, Wen Fang Tan, Guang Yu 出版年：2011
A control method for 100 nm scale motion platform driven by linear servo motors is investigated using a PMAC controller. The control of speed and acceleration is improved by adjusting the PMAC parameters. High-quality sp...
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGYLiu, Can Wu, Jing-quan Liu, Huan-lao Li, Guang-hui Tan, Guang-yu 出版年：2016
Some broken end mills with many brittle breakage sections were collected, and the geometry features of these sections were summed up. As for minor breakage, the breakage sections were narrow planes parallel to the tool e...
A series of experiments were conducted to study the performance of a coated cemented carbide tool in high speed milling of Ti-6Al-4V alloy. Experimental measurements of three components of the cutting forces were perform...
ADVANCES IN MATERIALS MANUFACTURING SCIENCE AND TECHNOLOGY XIVPeng, W. F. Li, G. H. Wu, P. Tan, G. Y. 出版年：2012
This paper adopts with a PMAC Programmable Multi-axis Controller to control a linear motor through adjusting PID + velocity and acceleration feedforward parameters of the control card. The motor can reach 50-nm precision...
渝公网安备 50019002500408号 违法和不良信息举报中心